Nickel-Copper alloy electrode. High strength, corrosion resistant electrode for welding wrought and cast forms of commercially pure nickel; joining nickel alloys to steel; surfacing steel with nickel, etc. Aufhauser 42 is widely used in the chemical, food, dairy and oil refining industries (but is not recommended where sulfur or lead are present).
S Ni 6082 (NiCr20Mn3Nb) ERNiCr-3 2.4806 . Characteristics and typical fields of application GTAW rod for welding of nickel-base alloys, high-temperature and creep resisting steels, heat resisting and cryogenic materials, low-alloyed problem steels and dissimilar joints. Ferritic- Casting Material:Precipitation-Hardening Stainless Steel ERNiCr-3 (alloy 82) wire to minimize notch sensitivity. Machining:Typical machining speeds for 17-4PH, using high speed steel tools are:Operation Speed Feed SFPM IPR Turning, 80-95 0.015-0.007 Single Point Drilling 1/4 dia 50 0.004 3/4 dia 50 0.008 Reaming under 1/2 60 0.003 over 1/2 60 0.008
Inconel 82, ERNiCr 3 Filler Metal Wire & Rod Supplier . USAERNiCr 3.Germany DIN, WNr2.4648, 2.4806. Japan JISYNiCr 3.England BSNA35. Client can procure smaller quantities of Inconel 82, Alloy 82, ERNiCr 3, UNS N06082 Filler Metal Wire & Rod products online ready stock from us at any destination by just sending us an email at This email address is being protected from ERNiCrCoMo-1 - Weld WireWeld Wire3/32 x 36 1/8 x 36. Application ERNiCrCoMo-1 is used for welding nickel-chromium-cobalt-molybdenum base material using both the gas tungsten arc and gas metal arc process. Also other cast heat-resisting alloy and dissimilar metals for high temperature service up to 2100º F.
3/32 x 36 1/8 x 36. Application ERNiCu-7 (NA60) is a copper-nickel alloy base wire for GMAW and GTAW welding of Monel alloys 400 and 404. Also used for overlaying steel after first applying Layer of 610 nickel. Exotic Corrosion Resistant Alloys - SPECIALTY METALSCorrosion Resistant Alloys or CRA are a Specialty. We have full traceability and supply our Material Certs with every order. Alloy 400 Alloy 400 is a ductile nickel-copper alloy with resistance to a wide range of corrosive environments. alloy K500
pairing high alloy heat and corrosion resistant castings of the same general composition, designated H K by the Alloy Casting Institute. Available in GTAW, GMAW and SMAW. ER316LMn Midalloy 316LMn (Din 1.4455) is an austenitic stainless steel wire primarily used in the cryogenic industry to obtain impact toughness and high strength. Guidelines for - Nickel InstituteGroups I, II, and III are predominately used for corrosion-resistant services, the Group IV alloys are used where higher strength is needed, although with usually some small sacrifice of corrosion resistance. Some physical properties and their influence on welding are shown in Table 2. Corrosion resistance of nickel alloy welds
Inconel 625 is actually a non-magnetic and a nickel-based alloy that is exhibiting wide range of working temperature, from cryogenic temperature to 2000 Deg F. The material is known popularly for having features like high tensile strength, stress corrosion cracking resistance, pitting resistance, stress corrosion cracking resistance, crevice Nickle Welding Wire - ERNiCr-3 Nickle Welding wire NiCrFe-wire/rod for joining NiCr-alloys, sub-zero tough nickel alloys down to 196°C, heat resisting austenitic steels and dissimilar steels up to + 550°C. Scale resistant in air and oxidising combustion gases up to + 1000°C. Chemical Composition Element by weight (%) :Ni:Bal. C:0,02 Cr:20,0 Mn:3,0 Fe:2,0 Nb:2,5 Mechanical Properties :
Alloy:UNS:Specifications:AWS/ASME:AMS:Other:HAYNES® 25:R30605-AMS 5796-HAYNES® 82:N06082:SFA / A 5.14 (ERNiCr-3) AMS 5836-HAYNES® 188:R30188-AMS 5801 TIG (GTAW) and MIG (GMAW) Filler Metal ProductsAlloy:UNS:Specifications:AWS/ASME:AMS:Other:HAYNES® 25:R30605-AMS 5796-HAYNES® 82:N06082:SFA / A 5.14 (ERNiCr-3) AMS 5836-HAYNES® 188:R30188-AMS 5801
Alloy, Corrosion-Resistant, Round Bars, 20Cr - 35Ni - 35Co - 10Mo Vacuum Induction Plus Consumable Electrode Vacuum Remelted Solution Heat Treated and Work Strengthened F 2527 R30035 Standard Specification for Wrought Seamless and Welded and Drawn Cobalt Alloy Small Diameter Tubing for Surgical Implants (UNS R30003, UNS R30008, UNS R30035, UNS